S2K Commerce - Products Dropdown
Actions
S2K Commerce - Order Entry
Actions
Our 3 to 1 Epoxy Activator forms an
easy to use 2 component 100 % solids epoxy system when mixed with either of our
available epoxy resins in a ratio of three parts Resin ( A side ) to one part
Activator (B side ) by volume. It Is significantly faster setting then our 2 to
1 system with improved chemical and solvent resistance and generally improved
physical properties. When mixed with our Standard Epoxy Resin it forms a
thicker high viscosity system more suited to adhesive bonding and casting
applications as it will generally form a tougher stronger plastic with better
adhesion and very good resistance to hydrocarbon fuels and ethanol. When used
with our Laminating Epoxy Resin it will form a thinner liquid more appropriate
for wetting out fiberglass and other reinforcements it will have a slightly
longer Gel Time and form a plastic with more flexibility, slightly less solvent
resistance and lower HDT. Both systems cure to a tough, hard, blush free, amber
colored plastic, with good physical properties, chemical and solvent
resistance, excellent resistance to water and good adhesion to wood, glass,
metals, and most other plastics.
As with all adhesive compounds bonding surfaces should be
clean and free dirt or grease.
system, that does not cure rigid hard, and will allow for the temperature driven expansion stresses
involved in most construction applications. The material features an easy to use 1 to 1 by volume mix ratio and excellent adhesion to most construction materials. This material is most useful for the rehabilitation of dry rotted wood and will in most cases restore it to a normal hardness and stop
further degradation of it.
With the proper loading of clean sand aggregate the material can make an excellent concrete
patching compound as well
As with all adhesive type compounds proper surface preparation is essential for good bond strength, additionally recoating of this material should be accomplished before the material is thoroughly cured generally in less then 24 hours. If the material has cured hard and tack free a light sanding and solvent wash may be necessary before recoating.
system, that does not cure rigid hard, and will allow for the temperature driven expansion stresses
involved in most construction applications. The material features an easy to use 1 to 1 by volume mix ratio and excellent adhesion to most construction materials. This material is most useful for the rehabilitation of dry rotted wood and will in most cases restore it to a normal hardness and stop
further degradation of it.
With the proper loading of clean sand aggregate the material can make an excellent concrete
patching compound as well
As with all adhesive type compounds proper surface preparation is essential for good bond strength, additionally recoating of this material should be accomplished before the material is thoroughly cured generally in less then 24 hours. If the material has cured hard and tack free a light sanding and solvent wash may be necessary before recoating.
The material features a highly thixotropic, paste-like consistency, which hangs well in thick sections on vertical and overhead surfaces.
The material cures to a hard, blush-free, amber- colored, high-strength, moisture-resistant plastic with excellent adhesive properties.
Additional recoating of this material should be done before the material is thoroughly cured.
If the material has cured hard and tack-free, a light sanding and solvent wash is advisable before recoating.
Epoxy cures faster at higher temperatures and in thicker layered applications.
Directions for Use:
Step 1: Required prep will vary according to application surface:
Ceramics, Composites, Plastics & Wood Must be oil free and sanded 80 grit or rougher.
Glass Must be sanded with 220 grit or lower until shine is removed.
Metals All metals must be carefully degreased with trisodium phosphate (TSP). Depending on the type of metal, prep work may vary.
Step 2: Be sure to clean the application site, removing all dust and debris.
Step 3: FGCIs Superbond Base Resin may be used with any of the three Activators, which differ in curing time:
Standard Activator
Medium Activator
Fast Activator
Please refer to Properties Chart for gel time.
Step 4: Mix at a 1:1 ratio by volume or weight, equal parts Base and Activator.
Step 5: Stir thoroughly, being sure to scrape sides and bottom of container. For best results, do not mix more than a quart at a time.
The material features a highly thixotropic, paste-like consistency, which hangs well in thick sections on vertical and overhead surfaces.
The material cures to a hard, blush-free, amber- colored, high-strength, moisture-resistant plastic with excellent adhesive properties.
Additional recoating of this material should be done before the material is thoroughly cured.
If the material has cured hard and tack-free, a light sanding and solvent wash is advisable before recoating.
Epoxy cures faster at higher temperatures and in thicker layered applications.
Directions for Use:
Step 1: Required prep will vary according to application surface:
Ceramics, Composites, Plastics & Wood Must be oil free and sanded 80 grit or rougher.
Glass Must be sanded with 220 grit or lower until shine is removed.
Metals All metals must be carefully degreased with trisodium phosphate (TSP). Depending on the type of metal, prep work may vary.
Step 2: Be sure to clean the application site, removing all dust and debris.
Step 3: FGCIs Superbond Base Resin may be used with any of the three Activators, which differ in curing time:
Standard Activator
Medium Activator
Fast Activator
Please refer to Properties Chart for gel time.
Step 4: Mix at a 1:1 ratio by volume or weight, equal parts Base and Activator.
Step 5: Stir thoroughly, being sure to scrape sides and bottom of container. For best results, do not mix more than a quart at a time.